CALL +91 - 8447936087

PLUMBING DESIGN AND DETAILING COURSE FOR ALL ENGINEERS

Plumbing Designing Duration 45 Days Course

​​1. Plumbing Systems

a. Fundamentals of Plumbing System

b. Introduction, Definitions & Concepts

c. List of codes & Standards

d. Fixtures, Faucets and Fixture fittings

i. Washbasin

ii. Water Closet

iii. Bidet

iv. Bathtub

v. Shower

vi. Urinals

vii. Kitchen sink

viii. Floor Drain

 2. Design of Domestic Water Supply and Distribution System

a. Requirements of Water Supply system

b. Water Demand Calculations Water

c. Storage Calculations Underground Sump(UGS)sizing

Elevated storage Reservoir(ESR)sizing Internal Water

Supply System

d. Direct Pumping System

e. Hydro-pneumatic system

f. Over Head tank distribution system

g. Design Procedure for Internal Water Supply System

h. Flow rate (q) & Loading Unit (z)-From probability equation

i. Hazen Williams Formula for Head loss Calculation

Internal Water Supply Pipe sizing calculations

Pumping Calculations- HP/Watts

j. Number of tapping to be connected Heavier Size Pipes.

k. Material used in internal water supply system

l. . External. Water Supply System

m. Number of Population served

n. Number of Fixtures served by Each Pipe

o. Design Procedure for External Water supply System External

Water Supply Pipe Sizing Calculations Material used

in External water supply system

p. Water Supply Schematic Layout

 3. Design of Sanitary Drainage System

a. Requirements of Sanitary Drainage System

b. Types of Sanitary Drainage Systems

c. Single stack system

d. Single stack (partially ventilated) system

e. One Pipe System

f. Two Pipe System

g. System requirement for Internal Sanitary Drainage System

h. Internal Sanitary Drainage Pipe Sizing Calculations

i. Design Procedure for External Sanitary Drainage System

j. External Sanitary Drainage Pipe Sizing Calculations

k. Calculation of Slope by Manning’s formula

l. Calculating Depth of Inspection Chamber/Manholes

m. Sanitary Drainage Schematic Layout

n. Design of Storm Water Drainage System

o. Design of Basement Drainage System

p. Using Manning’s Formula and Rational formula

q. Storm Water Drainage Pipe Sizing Calculations

r. Material used in Sanitary Drainage system

 4. Drawings – Plumbing Layouts

a. Legends used in Plumbing

b. Legends used in Plumbing

c. Typical Floor Plan-Plumbing Layout

d. Enlarged Kitchen & Utility-Plumbing Layout

e. Riser Diagram for multi storied buildings.

 
5. The Other aspects

a. Life Cycle of the Project

b. Different stages in Design and Drafting

c. Communication between the different teams,

d. Mode of communication using standard formats

And templates

e. Project Management Tools

f. Maintaining Safe and healthy working environment

 
6. Employ ability and Skills Improving

a. Resume Writing Skills Improving

b. Interview Skills En powering

c. En Powering of Interpersonal Relationships.

d. Stress Management.

e. Positive Attitude Development.

f. Self-Motivation.

Electrical design and drafting for electrical engineers and construction professionals

​1. General

2. Codes & Standards to be followed

• Indian electricity rules

• National electrical code of India (NEC)

• National building code of India (NBC)

• Applicable standards issued by Bureau of Indian standards (BIS)

• Institute of Electrical & Electronics Engineers (IEEE)

• Regulations of local fire authorities

• Requirements stipulated by Pollution control Board for Noise & Air

3. Electrical equipment’s and its application used in the installation

• Control devices

• Measuring devices

• Circuit protection devices

• Transformers

• Diesel generators

• Capacitors

• Bus ducts, Bus-bars, Cables (HT/LT) & wires

• Motors & Pumps

• Luminaries – General  & Emergency

• Isolators & socket outlets

• UPS/Inverter & Battery banks

• Earthing or Grounding

• Lightning arrestor

4. Means of electrical distribution for installation

• Panels (LT)/Switch Board/Motor control centers (MCC’s)/Final Distribution boards (DB’s)

• Cable trays, trunking or raceways, conduits & underground Pipes (Concrete/PVC)

5. Major electrical loads used in the installation

• Lighting load – Internal & external

• Utility power load

• HVAC loads like FCU’s, Fans etc.

• PHE & FF loads like Water transfer pumps, Booster pumps, Fire Fighting pumps, Jockey pumps etc

• Lifts (Elevator) load

• Computer & data center (Server) loads for office building

6. Electrical design calculations

• Load & maximum demand calculation

• Transformer sizing calculation

• DG sizing calculation

• Short circuit calculation

• Voltage drop calculation

• Capacitor sizing calculation

• Cable sizing calculation

• Earthing calculation

• Lightning calculation

• UPS/Inverter sizing calculation

• Battery sizing calculation

7. Various design stages & Sequence of electrical design procedure

Concept design stage

• Understanding the building plans, elevations & sections

• Gathering specific data from the utilities (Electricity board)

• Understanding clients specific requirements

• Preparation of basis of design which should include the cost estimate.

Schematic design stage

• Preparation of Load calculation to arrive maximum peak demand

• Sizing of all Equipment’s, cables, cable trays

• Electrical design calculations

• Preparation of single line schematic of electrical distribution system with metering options

• Preparation of lighting, small power, earthling & miscellaneous layouts

• Preparation of technical specification

Detailed design stage

• Preparation of detail layouts including sectional details wherever required

• Coordination with other services like HVAC,PHE & FF layouts

• Preparation of bill of quantities (BOQ)

• Preparation of shop drawings based on the tender drawings issued by

Electrical consultants for installation.

• As built drawings shall be prepared and handed over to client’s representative

PLUMBING DESIGN AND DETAILING COURSE FOR ALL ENGINEERS